Nov 23, 2024
HEP 456 Module 6 Section 14 Communication and Dissemination of The Findings Arizona State University
HEP 456 Module 6 Section 14 Communication and Dissemination of The Findings HEP 456: Health Promotion Program ā¦
Router_A is currently the OSPF designated router (DR). When will an election occur for a new DR?
None of the above.
When the point-to-point interface of the current DR goes down
Answers A, B, and C are correct.
Correct!
When the DR fails
When a new router comes up with a higher OSPF priority
Router1 and Router2 are configured to run the OSPF routing protocol. The two routers are connected via point-to-point serial interfaces. Select the most likely sentence that describe how OSPF works between the two routers.
Router1 may become DR on the point-to-point link if it comes up first.
Correct!
None of the above
Router2 may become DR if it has higher priority than Router1.
Router1 may become BDR if it has lower priority than Router2.
Answers A, B, and C are correct.
An OSPF router is configured with a basic hello timer of 10 seconds. What will the default dead interval timer be?
40 seconds
10 seconds
60 seconds
20 seconds
30 seconds
The OSPF packet header contains _____.
the area priority field
Correct!
the Type code for OSPF packet type
the router autonomous system field
the DROther field
Answers A and B are correct.
Which command will verify that a router that is running OSPFv2 has formed an adjacency with other routers in its OSPF area?
show ipv6 interface brief
show running-configuration Answered
Single area OSPFv3 has been enabled on a router via the ipv6 router ospf 5 command. Which command will enable this OSPFv3 process on an interface of that router?
None of the above
ipv6 ospf 0 area 0
ipv6 ospf 0 area 5
ipv6 ospf 5 area 5
Correct!
ipv6 ospf 5 area 0
Which command will provide information specific to OSPFv3 routes in the routing table?
show ip route ospfv3
show ipv6 route
show ip route ospf
show ip route ospf
Correct!
show ipv6 route ospf
A network administrator enters the command ipv6 router ospf 110 in global configuration mode. What is the result of this command
The router will be assigned an autonomous system number of 110.
The OSPFv3 AS number will be assigned an ID of 64.
The router will be assigned a router ID of 110.
The reference bandwidth will be set to 110 Mb/s.
Correct!
None of the above
Which command should be used to check the OSPF process ID, the router ID, networks the router is advertising, the neighbors the router is receiving updates from, and the default administrative distance?
show ip ospf
show ip ospf neighbor
Correct!
show ip protocols
show ip ospf interface
None of the above
A router in OSPF router has a data rate of 64 Kbps on one of its interfaces. What will the OSPF cost of that link be?
128
100
110
90
Correct!
1562
R1 is currently the DR router. R2 is currently the BDR router. R3 is currently the DROther. Your IT Manager has asked you to make R3 the DR and R2 the BDR. Which answer will achieve that goal?
Shutdown R3, R2, and R1 interfaces and bring them back up in the reverse order.
Boot up R3 first followed by R2, and then R1.
Change the priority number on R3 to be the highest.
Answers A and B are correct.
Change the priority on R2 to be the second highest.
(TCO 5) Ciscoās routers use this first to determine router-ID in OSPF. Assume IP addresses are configured on Physical and Loopback Interfaces only.
Largest loopback IP addresses
Lowest loopback IP addresses
IP addresses on physical interfaces
None of the above
Most active IP address
Powered by TCPDF (www.tcpdf.org)
